Right here down the page you can locate additional dependable content concerning A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily obtainable, the job can move speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the work and also fit trying it. Instead of hiring a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will aid you mount a brand-new bath tub in your shower room if you have already acquired a new bathtub as well as do not require to alter the plan of your previous water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines are in location between the faucet and also the sink. Secure the faucet in position with the producer offered backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous type should be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub up until the level reads degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the water system and also check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub must wait till the bathtub has been utilized at the very least once as this will settle it right into its last position.
Getting ready for the Setup
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in complications with moisture as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Installing A Bathtub? Put a comment down below. We would be interested to see your feelings about this page. We hope to see you back again soon. If you please take the time to distribute this blog if you liked it. Thank-you for your time spent reading it.
Estimate